Woodpecker Birdhouse Cheyenne WY
Cherry Creek Nursery
114 Ponderosa Trl
Data Provided By:
Prometheus Life Sciences
2510 Warren Avenue
Fort Collins, WY
which means it is the same FLavoring used in gourmet foods. There is often a noticeable difference in joint pain and stiffness within a short 24 hours."
The Home Depot
1740 Fleischli Pkwy
Frontier Fashion Mall
1400 Del Range Blvd
Murdoch's Ranch & Home Supply
3773 E Lincoln Way
Mcintyre's Garden Center
3515 Del Range Blvd.
Products / Services
Flower Seed, Seed, Wildflower Seed
Data Provided By:
1782 Dell Range Boulevard
Bloedorn Lumber Building Mtrls
1551 Stillwater Ave
LOWE'S OF CHEYENNE, WY
1608 PRAIRIE AVENUE CHEYENNE, WY, 82009
Capital Lbr True Value Hdwe
1222 Dunn Ave
Data Provided By:
How To: Woodpecker Box
Build an Easy Box for Golden-fronted, Red-headed, and Hairy Woodpeckers
Download detailed plans you can use to build your own woodpecker box. The plans for this box were taken from The Original Birdhouse Book , which features 26 birdhouse, nesting shelf and nesting box plans you can build.
Tools You'll Need
Brace , with 1/2-in. bit and expansion bit up to 2-1/2 in. or keyhole saw
Drill , with assorted small bits
Golden-fronted, Red-headed, and Hairy Woodpecker Box Cedar boards or exterior plywood , 5/8 in., 36-1/4 by 17-1/4 in.:
Bottom-6 by 6 in.
Sides (2)-each 14-3/4 by 13-3/4 by 6 in.
Back-17 by 7-1/4 in.
Front-14 by 7-1/4 in.
Roof-9-1/4 by 9-1/4 in.
Fourpenny galvanized box nails
Sixpenny galvanized box nails (2)
Galvanized nail or right-angle screw hook, about 1.5 in. long
Sixteen-penny galvanized nail
Post (optional)- 4 by 4 in. or 4 by 6 in., 14 ft. long galvanized metal pole
Strapping brackets for mounting box
Predator baffle (pole- or post-mounted)
- After you have looked over the drawings and decided which box or boxes to build, lay out the parts, with a square and pencil, on the weather surface. Saw out the pieces, plane the splinters, mark the parts, and put them aside. If the interior surface of the front, back, and sides is smooth, roughen it-really scar it up-with the corner of a rasp. This helps young birds gain a foothold when trying to climb to the hole when exiting the box. Cut back the corners of the bottom piece.
- In the back panel, drill a 1/2-in. hole 2 in. down from the top and centered horizontally. (On the downy woodpecker box, center the hole 1 in. down.) Bevel the back 1/8 in. toward the interior surface. On the front panel, bevel 1/8 in. toward the weather surface.
- Drill the entrance as shown for each box, using a keyhole saw or expansion bit on the larger boxes. If you have neither, then draw the circle and drill a series of 1/2- to 1-in. holes just inside the circumference. Chew out the hole with a rasp, rounding the edges. Woodpeckers won't mind a few irregularities.
- Draw a line across the interior surface of the back, 2-3/4 in. up from the bottom. Extend it across the edges and the weather surface.
- Next, draw a line across the interior surface of the front panel, 1 in. up from the bottom, and extend it over both edges.
- Draw 1 more line across the interior surface of the right side panel, 1 in. up from the bottom, and extend it across the edges.
- To begin assembly, start 2 nails on the weather surface of the right side panel to come out 1/4 in. below the line. Do not get the nails too close to the edges of the side panel, because the bottom edge, to which you will nail the side panel, has the corners cut off. Place the "decornered" bottom on edge, against a wall. Lay the side panel across, with the line matching the interior surface of the bottom. The wall will...
Author: Bird Watcher's Digest
Copyright2010 Bird Watcher's Digest
Click here to read the rest of this article from birdwatchersdigest.com